Code: HP2-Z18
Vender: HP
Exam Name: Network Infrastructure AIS 2011
Certs Name: HP ASE Wireless Networks
Question: 1
Which HP E-Series switch models display the following prompt in the interface configuration context? (Select two)
HP Switch (eth-A24)#
A. E8212zl
B. E6600-24G
C. E5412-96GZI
D. E2910-24Gal
E. E350CM8G-POEyI
Answer: A,C
Question: 2
When Spanning Tree Protocol is enabled, which devices receive outbound LLDP advertisements from an HP E-Series switch?
A. those with interfaces in VLAN 1
B. those that receive the switch’s broadcasts
C. those that are directly connected to the switch
D. those in the LLDP multicast group
E. those not blocked by Spanning Tree Protocol
Answer: C
Question: 3
You must assign a friendly name to port B24 on an HP E5406 zI switch. Given the following prompt, which command must you enter next to complete this task?
E5406#
A. configure
B. name int b24 <name>
C. interface b2 4
D. manager
Answer: A
Question: 4
You are at the manager level prompt In the CLI of an HP E3500 yI switch. Which options are available at this prompt? (Select two)
A. assign IP address to VLAN interface
B. enable IP routing
C. restart the switch
D. disable ports
E. update software
Answer: C,E
Question: 5
Which statements are true about the primary and secondary flash areas of an HP E-Series switch? (Select two)
A. The primary area contains the switch’s operating system, which is automatically copied to the secondary area whenever the switch is restarted.
B. The switch can be started using the software stored in either area.
C. The software stored in the primary area is always used to start the switch.
D. The primary area always contains the most recent software version; the secondary area contains an earlier version to be used if the primary version.
E. The software in each area is stored and managed independently
Answer: B,E
Question: 6
You make configuration changes to the running configuration of your HP E3500 yI switch. Which command saves these changes to your startup configuration?
A. save running-config
B. copy running-config startup-config
C. write memory
D. write config
Answer: C
Question: 7
Port B1 on an HP ProCurve 5406zI switch is an untagged member of VLAN 155 and not a tagged member of any VLAN PortC1is a tagged member of VLAN 155 and an untagged member of VLAN 100. You issue the following command:
5406zl (config)# no vlan 155
Why do you receive the following prompt?
The following ports will be moved to the default VLAN: Bl Do you want to continue? [y/n]:
A. The CLI always issues this prompt when deleting a VLAN
B. The CLI will not allow you to orphan a port
C. The CLI will not delete a VLAN with any port membership.
D. All ports must be moved to the default VLAN before you can delete the VLAN.
Answer: D
Question: 8
Refer to the exhibit below.
You enter the following command at the switch’s CLI: E5406 (vlan-100) # no untag a24
A. Why does this command fail?
B. PortA24 is not a member of VLAN 100.
C. Port A24 must be a member of at least one VLAN
D. VLAN 100 must have at least one port member
E. no untag a24 is an invalid CLI command
Answer: B
Question: 9
At the CLI of an HP E2610-24 switch, you have assigned ports 1-4 to VLAN 50 as untagged members.
The E2610 is connected through port 24 to an E5406 zl switch. All other configuration parameters on
the E2610 are at default settings. The E5406 is configured with a VLAN 50 IP address of
192.168.50.1/24. IP routing is enabled. It is connected to the E2610 through port B24, which is a tagged member of VLAN 50 On the E2610, which command will enable the E5406 to act as a default gateway for VLAN 50 clients?
A. E2610 (config) # vlan 50 ip address 192.168.50.2/24
B. E2610 (config) # ip default-gateway 192.168.50.1
C. E2610 (config) # ip route 192.168.50.0/24 vlan 50
D. E2610 (config) # vlan 50 tag 24
Answer: D
Question: 10
What is the effect of the following command entered at the CLI of an HP E3500 yI switch? E3500 (config) # timesync sntp
A. The switch will use SNTP as its time synchronization protocol
B. The switch will provide SNTP services to all connected VLANs.
C. The switch’s clock will be synchronized with a configured SNTP server d.
D. The switch will broadcast for an SNTP server.
Answer: A
HP2-Z18 Exam – For getting more latest questions click the link below : http://www.selftesttraining.com/HP2-Z18.html
HP2-Z18 Online Test 